Amada HFA250W
Band Saw

The Amada HFA250W Band Saw is a horizontal NC Controlled Full Automatic Metal Cutting Band Saw.

Fully automatic band saws with very accurate material indexing controlled by NC-positioning.

Cutting Capacity: Round (Diameter)? 0.5″ – 10″

  • 5 HP
  • 1-1/4″ Blade
  • Automatic
  • NC Back Gauge
  • Self Diagnostics
  • Variable Blade Speed
  • Wheel Cover Limit Switch

Saw Head Frame

  • The rigid ‘C’ section frame carries the mountings for the two band wheels, heavy-duty worm drive gear reducer, the band drive motor, and saw guide arm mounting supports.

Band Wheels & Drive System

  • The band wheels are cast iron for long, productive life. The deflection free 1.38 inch (35 mm.) wheel spindles ensure the wheels run true regardless of tension stress or cutting loads. The spindle assemblies incorporate tapered roller bearings for greater rigidity and long service life. The wheel tracks the blade so that the back of the band is contacts the wheel flanges to support the band. The drive motor is coupled to the transmission through a variable speed pulley.

Wide Blade (1 1/4 inch, 34mm)

  • The wider blade, for this capacity machine, can make full utilization of the large band drive motor (5 hp, 3.7 kW) when cutting all shapes and alloys.

Drive Wheel Transmission

  • The drive wheel transmission is designed and built by Amada to provide high-efficiency speed reduction, which requires no external cooling, to deliver more power to the large diameter drive hub. This hub ensures that this developed torque is transferred to the blade with no strobing, enabling the machine to efficiently cut high alloys as well as free machining materials.

Pressure/Flow Feed Control

  • The independent pressure and flow controls in series ensure the optimum cutting rate can be obtained regardless of section or alloy being cut. The pressure control determines the cutting force applied to the blade and the flow control sets the maximum fall rate of the head. For example, for difficult to machine materials the pressure is set higher than free machining alloys and the flow is set lower, as shown on the escutcheons above the control knobs.

Idler Wheel Motion Detector

  • The wheel motion detector will turn off the blade drive in the case where a blade breaks or is jammed in the workpiece. This feature also prevents premature wear on the drive wheel from a stalled band.

NC Control of Cutting and Auto Cycle

  • The NC index control provides greater flexibility and expanded capabilities compared to a The controller enables the operator to specify the index home position – forward and clamped or at the index position and open. The controller also determines the speed of the index vise motion forward and reverse. It provides independent ramp cycles for the forward and rear traverse. The speed ramp up and down for moving the work piece is slower when it is positioning the work piece than when it is moving without work. This feature provides more accurate indexing of the work piece.

Smart Multiple Index

  • The machine control has the capability to make multiple full length index strokes until the length remaining to index is less than the full index stroke (15.8 in., 400mm.) the last index stroke is the remaining length.

Band Deviation Monitor ®

  • This patented cutting control device can reduce scrap by warning when the blade is no longer cutting within the operator’s settings for deviation. The allowable deviation limit is set by the operator independently for each direction. The digital deviation indicator will flash when the blade deviation exceeds either maximum. If the deviation continues to exceed the preset value the NC controller will stop the cutting, raise the saw head and display the exceeded deviation value.

Split Front Vise

  • The work holding vise is split so that it clamps the work piece on both sides of the cutting plane. This additional support in front of the cutting plane minimizes the burr on the cut pieces.

Powered Chip Conveyor

  • The powered chip conveyor auger automatically removes the saw chips from the saw while draining the cutting fluid back into the fluid reservoir. The automatic chip conveyor greatly reduces cleanup time and enables the machine to run longer without operator cleanup.

Call the Ocean Machinery sales team TODAY at (954) 956-3131 or Toll Free 1 (800) 286-3624 or fill out our online info request form for more information on the Amada HFA250W Band Saw.

Categories: ,

Amada HFA250W
Band Saw

FEATURES+
  • Blade Deviation Monitor
  • Chip Conveyor
  • Full stroke Vise
  • Motion Detector
  • NC Back gauge
  • Pressure Flow Valve
  • Self Diagnostics
  • Split Vise
  • Variable Blade Speed
  • Wheel Cover Limit Switch
SPECS+

 

Cutting Capacity – Round (diameter) 0.5″ – 10″ (13 – 250 mm)
Cutting Capcity – Rectangle (W x H) 11.8″ x 10″ (300 x 250 mm)
Work Load Capacity 3,307 lbs (1,500 kg)
Blade Dimensions 11’6″ x 0.042″ x 1-1/4″ (3505 x 1.066 x 32 mm)
Blade Speed 89-295 ft./min, 60Hz Stepless (24-90 m/min, 60Hz Stepless)
Tension Control Hydraulic
Vise Operation Type Hydraulic Full-Stroke Cylinder
Blade Saw Motor 5 HP (3.7 kW)
Hydraulic Pump Motor 1 HP (0.75 kW)
Cutting Fluid Pump Motor 1/4 HP (0.18 kW)
Power Supply Voltage AC220±10%, 3 PH, 60 Hz (Or AC440V, 3PH, 60Hz)
Power Requirement 8.3 kVA
Cutting Fluid Tank Capcity 22.4 gal (85 Liters)
Cutting Fluid Pump Type Electric
Hydraulic Tank Capcity 7.9 gal (30 Liters)
Chip Disposal Chip Conveyor
Material Index Mechanism Shuttle Vise
Stroke 15.75″ (400 mm)
Machine Dimensions – Head Up Position 76.9″ x 93.3″ x 69.8″ (1953 x 2370 x 1772 mm)
Machine Dimensions – Head Down Position 76.9″ x 93.3″ x 50.6″ (1953 x 2370 x 1285 mm)
Table Height (Above Floor) 27.6″ (700 mm)
Machine Weight 3,307 lbs (1,500 kg)
MEDIA+

Please call for more information about Amada band Saw Model HFA250W 1 (800) 286-3624

OPTIONS+

AXCELA G SERIES Band Saw Blades

High-performance Carbide Tipped Band Saw Blades
High-quality carbide tips and the dove tail tooth shape. AXCELA makes incredible cutting speed for hard to cut material.

BCTBR Band Saw Blade

Multi Faceted Carbide Tipped Blade

Designed exclusively for heat-resistant alloys, nickel-based alloys, titanium alloys, and special cast tensile steels, all with high tensile strength of over 142,000 psi. It features ultra-hard, diamond sharp carbide tipped teeth that resist low thermal conductivity and abrasion that can quickly break down conventional bi-metal type bands.

MAGNUM HI-LO Band Saw Blade

Patented Varying Tooth Height and Set M-71 Bi-metal Blade
High-quality carbide tips and the dove tail tooth shape. AXCELA makes incredible cutting speed for hard to cut material.

Hi-Lo Band Saw Blade

Varying Tooth Height Design, M-42 Welded Edge

The Hi-Lo blade features a high and low teeth height design and a 15-degree rake angle. The blade is ideal for cutting hard steels.

CHIP BREAKER Band Saw Blade

Patented Gullet Design
Designed to reduced heat generated at increased chip load. With reduced tooth stripping and breaking this equates to the lowest possible cost per square inch of metal cutting.

SGLB Band Saw Blade

M-42 Bi-metal Blade

The SGLB was designed to cover a broad range of cutting applications and to provide maximum efficiency in sawing wear-resistant tool steels. The blade’s tough M-42 cobalt edge resists heat and abrasion, while the varied pitch tooth form expands the ranges of sizes and shapes that can be sawed successfully without changing blades.

COBALT8 Band Saw Blade

Amada Modified M42 High-Speed Steel Bi-Metal Blade
General-purpose blade ideal for cutting mild steel and structural steel. “Chip Curler” tooth shape and unique set pattern result in longer blade life.

SMARTCUT BAND Band Saw Blade

Thinner Blade of SGLB and Magnum Hi-Lo

Thinner more than 10% from regular SGLB or Magnum Hi-Lo. Specialized Blade for PCSAW330

PROTECTOR EX M42 Band Saw Blade

Exclusive use for structural steel with M-42 Edge. Which has both strength against tooth chipping and high wear resistance. PROTECTOR EX added to the back face of the tooth tip prevents excessive cutting.

PROTECTOR Band Saw Blade

Exclusive Use for Structual Steel with M-30 Matrix Bi-metal Blade

Exclusive use for structural steel. Protector provides long blade life and prevents tooth breakage, eliminating excessive tooth stripping. It can withstand the shock of interrupted cuts, allowing for heavier penetration for faster cutting rates. Protector uses a broaching style set pattern designed to eliminate pinching, which prevents the blade from binding the cut.

MGLB Band Saw Blade

General Purpose Matrix Bi-metal Blade

The MGLB is best suited for cutting structural shapes, tubing and stacks of mild steel pieces. The MGLB allows band saw machines to cut a wide range of material sizes and shapes without requiring a change of blades. Its tough high-speed steel teeth resist chipping, stripping and abrasion. It can also tolerate the occasional improper speeds and feeds that are often used by inexperienced saw operators.

Description

The Amada HFA250W Band Saw is a horizontal NC Controlled Full Automatic Metal Cutting Band Saw.

Fully automatic band saws with very accurate material indexing controlled by NC-positioning.

Cutting Capacity: Round (Diameter)? 0.5″ – 10″

  • 5 HP
  • 1-1/4″ Blade
  • Automatic
  • NC Back Gauge
  • Self Diagnostics
  • Variable Blade Speed
  • Wheel Cover Limit Switch

Saw Head Frame

  • The rigid ‘C’ section frame carries the mountings for the two band wheels, heavy-duty worm drive gear reducer, the band drive motor, and saw guide arm mounting supports.

Band Wheels & Drive System

  • The band wheels are cast iron for long, productive life. The deflection free 1.38 inch (35 mm.) wheel spindles ensure the wheels run true regardless of tension stress or cutting loads. The spindle assemblies incorporate tapered roller bearings for greater rigidity and long service life. The wheel tracks the blade so that the back of the band is contacts the wheel flanges to support the band. The drive motor is coupled to the transmission through a variable speed pulley.

Wide Blade (1 1/4 inch, 34mm)

  • The wider blade, for this capacity machine, can make full utilization of the large band drive motor (5 hp, 3.7 kW) when cutting all shapes and alloys.

Drive Wheel Transmission

  • The drive wheel transmission is designed and built by Amada to provide high-efficiency speed reduction, which requires no external cooling, to deliver more power to the large diameter drive hub. This hub ensures that this developed torque is transferred to the blade with no strobing, enabling the machine to efficiently cut high alloys as well as free machining materials.

Pressure/Flow Feed Control

  • The independent pressure and flow controls in series ensure the optimum cutting rate can be obtained regardless of section or alloy being cut. The pressure control determines the cutting force applied to the blade and the flow control sets the maximum fall rate of the head. For example, for difficult to machine materials the pressure is set higher than free machining alloys and the flow is set lower, as shown on the escutcheons above the control knobs.

Idler Wheel Motion Detector

  • The wheel motion detector will turn off the blade drive in the case where a blade breaks or is jammed in the workpiece. This feature also prevents premature wear on the drive wheel from a stalled band.

NC Control of Cutting and Auto Cycle

  • The NC index control provides greater flexibility and expanded capabilities compared to a The controller enables the operator to specify the index home position – forward and clamped or at the index position and open. The controller also determines the speed of the index vise motion forward and reverse. It provides independent ramp cycles for the forward and rear traverse. The speed ramp up and down for moving the work piece is slower when it is positioning the work piece than when it is moving without work. This feature provides more accurate indexing of the work piece.

Smart Multiple Index

  • The machine control has the capability to make multiple full length index strokes until the length remaining to index is less than the full index stroke (15.8 in., 400mm.) the last index stroke is the remaining length.

Band Deviation Monitor ®

  • This patented cutting control device can reduce scrap by warning when the blade is no longer cutting within the operator’s settings for deviation. The allowable deviation limit is set by the operator independently for each direction. The digital deviation indicator will flash when the blade deviation exceeds either maximum. If the deviation continues to exceed the preset value the NC controller will stop the cutting, raise the saw head and display the exceeded deviation value.

Split Front Vise

  • The work holding vise is split so that it clamps the work piece on both sides of the cutting plane. This additional support in front of the cutting plane minimizes the burr on the cut pieces.

Powered Chip Conveyor

  • The powered chip conveyor auger automatically removes the saw chips from the saw while draining the cutting fluid back into the fluid reservoir. The automatic chip conveyor greatly reduces cleanup time and enables the machine to run longer without operator cleanup.

Call the Ocean Machinery sales team TODAY at (954) 956-3131 or Toll Free 1 (800) 286-3624 or fill out our online info request form for more information on the Amada HFA250W Band Saw.

© Copyright 2024, Ocean Machinery Inc.